The Tour Master Synergy® 2.0 Heated Leather Gloves are made with drum-dyed goatskin leather with Raingard® to keep your hands warm and dry if you get caught in cold and rainy weather. This Synergy® 2.0 leather glove, when paired with the Tourmaster vest/jacket lines and chap/pant liners offer superior protection in colder weather and can give you the ability to go ride your motorcycle while your buddies say it is too cold.
Item Code: TourmasterSynergy2LeatherGloves Brand: Tour Master Color: Black Material: Goatskin Leather Gender: Unisex
Synergy 2.0 Gloves include the Power Lead Wiring Harness, Single Control Rheostat and an extended V-Split Connector (Required when using Synergy Gloves with Synergy Pant or Vest Liners).
Grade A, Aniline drum-dyed goatskin leather with a Raingard® waterproof and breathable barrier
Clarino® palm panel resists grip wear
100gm Polyfil Insulation increases warmth and heat retention
Lightweight and flexible steel fiber heating elements provide instant and even heat
A single rheostat is included and easily and accurately adjusts through a range of temperatures (dual rheostat controller optional)
A temperature sensor regulates the maximum and minimum heat levels to provide a consistent temperature
Soft Bemberg interior lining
Action expansion panels in the fingers help fine-tune the fit and increase comfort
Designed to be worn individually or connected to other Synergy 2.0 garments
360º full circumference wrist closure
Designed to operate in all weather conditions from a vehicle's 12-volt electrical system
Warmth without bulk or discomfort, making for a safer, more enjoyable ride
Lightweight, flexible steel fiber heating elements provide safe, even warmth
Expanding side panels help fine tune the fit and increase comfort
Water-resistant, single or dual rheostat available
Please measure across the palm of your hand starting at the top side of the base of your thumb (see image chart) using a cloth tape measure and choose your size from the chart below.Please note all measurements are in inches.Unisex sizes are listed in Men’s Sizes. Women’s sizes are provided for cross reference.
Comment: Believe me when I tell you to order two sizes bigger than you think you need. Also, these babies are not waterproof (soaked thru in the rain the other day) so use snowseal or other water sealer. Also, they are not as pictured; they do not have the pocket for the thermostat on the right glove. You will have a thermostat to attach to a strap for your leg though. All around good glove, just not entirely what they say it is.
Tour Master Synergy Leather Gloves
Comment: Gloves do what they're supposed to do. They DO NOT have a pocket on the right glove for the temp-controller and they are NOT WATERPROOF. You will have to strap the controller to your leg and route the cable thru your jacket. Measurments indicated I needed a Medium, I ordered a XL, and the fit was right on.
Ridden a few time now in 40 degree morning mist and the warmth was great.
Tourmaster Synergy 2 Leather Gloves Review
Comment: Bought a large using the chart. Gloves need to be in contact with fingers but that didn't happen. A week later purchased medium textile and same problem with finger size for skinny fingers. Like the material but size was too far off to for comfort. The Tourmaster controller modulates voltages versus steady power and it fails to satisfy at highway speeds - need to plug gloves directly to power.
Again, today we're taking a closer look at the Synergy 2.0 gloves. Now, these
gloves will not be available until late Fall 2013 but I wanted to show you a
couple of the features so that you can purchase the best product for you. These
gloves are available in two versions, a leather version and a textile version.
This is the video for the leather version. To see a video with uncanny
similarities to this video, but featuring the
textile version of this glove, click the link below to visit our website.
Unlike the original Synergy heated gloves, the 2.0 versions use either the new
single or dual Rheostat controllers so they no longer have controllers in the
gloves themselves. This does change the adjustability somewhat because you may
be sharing Rheostat function with other garments, depending on how you have
everything hooked up. But, the reduction of weight and bulk is completely worth
it in my opinion. Synergy didn't focus all of their efforts on warmth. These
gloves have numerous safety features as well. These gloves are constructed using
top grain cowhide. They feature padded protection for the top of the hand, the
ulna and the radius bones, and the fingers and palm of the hand. The radius
protectors are covered in Phoslite reflective material. There is adjustability
at the wrist and on the gauntlet, and the left thumb features a face shield
wiper. If you are wearing the gloves by themselves or with a vest, you will need
to use the extended v-split connector that is included with the gloves. Just
hold the leads in your hands when you put your riding jacket on, and you're all
wired up. If you are using these gloves in conjunction with the Synergy Heated
Jacket Liner, simply plug the gloves into the connectors located in the pockets
on the sleeves of the jacket liner. As with all heated products, be sure to
start your motorcycle before plugging the controller into the power lead. This
will protect your garments from any voltage spikes that can occur during